Britax Hi-Liner SG User Manual download pdf (Page 14)

HOW TO USE

USING LAP SEAT BELT WITH THE CHILD HARNESS

1. Right Hand Harness Strap

2. Left Hand Harness Strap

3. Cross Strap

4. Cross Strap Loop

5. Right Hand Harness Stray Loop

6. Cover Pad (not shown)

7. Storage Strap

HOW TO USE

D. Engage the seat belt tongue to the buckle

and adjust the seat belt to sit rmly but

comfortably around the child's pelvis. The

seat belt buckle should be located as low as

possible below the child's hip.

E. With the lap belt (or converted lap/sash)

adjusted to be a rm t on the child's thighs,

then adjust the Child Harness to remove

all slack in the shoulder straps but do not

tighten. Once adjusted, further adjustments

are necessary only to the upper extension

straps and to accommodate the growth of

the child.

F. Finally, fold the free end of the adjuster

strap, secure using the storage strap, then

place it into the top of the adjuster cover as

shown left.

G. Lengthen the harness at any time as shown

on page 21, by fully pressing the Adjuster

Button (1) whilst pulling the shoulder strap

(2) upwards.

The lap position of the seat belt must be adjusted rmly rst, and then the Child

Harness, so that the belt is not lifted off the child’s lap when the child harness is

adjusted. The Child Harness does not need to be tight.

Some vehicle seat belts are too short and you may experience some difculty tting

the converted lap-sash around your child. If so, adjust the Gated Slide nearer to your

child, ideally under the armrest and lap belt recess area, (ensure the Gated Slide

does not touch your child). This should provide more belt length to t your child,

but if the belt still will not t, try another location in the vehicle, e.g. side seat. If the

vehicle belts are still too short, then contact the vehicle manufacturer for advice on

longer seat belts.

Fold the

adjuster

strap and

secure with

Storage

Strap.

Storage

Strap

Adjuster

cover

26 27

Pull

adjuster

strap to

remove

slack

Fit the Child Harness as detailed on page 18.

Thread the lap seat belt through the Child

Harness strap loops as shown below. Ensure

there are no twists in the Child Harness, cross

strap and seat belt.

Important Note: Some vehicle seat belts are too

short and you may experience some difculty

tting the converted lap-sash around your child.

If so, adjust the Gated Slide nearer to your child,

ideally under the armrest and lap belt recess

area, (ensure the Gated Slide does not touch

your child). This should provide more belt length

to t your child, but if the belt still will not t, try

another location in the vehicle, e.g. side seat. If

the vehicle belts are still too short, then contact

the vehicle manufacturer for advice on longer

seat belts.

NOTE: Seat belt extenders should not be used if

the seat belt is not long enough to t around the

child. If a seat belt extender is used then the seat

belt buckle must not be in contact with the child.

Connect the Harness to the Versa-Tether™

Catch as detailed on page 18.

A. With the child seated, place each of the Child

Harness straps over each shoulder.

B. Feed the right hand strap (loop end) into the

cross strap loop to connect the two sides.

C. Feed the adult belt (lap belt or converted

lap/sash) through the harness loops,

ensuring that the cross strap loop does not

disconnect. Also ensure there are no twists

in the Child Harness, cross strap and seat

belt.

SLIDEGUARD™

Clip

Child Harness

strap loops

1 2 ... 9 10 11 12 13 14 15 16 17 18 19 20 21

Comments to this Manuals

No comments

Britax Hi-Liner SG User Manual Page 14

Comments to this Manuals

Related products and manuals for Car seat Britax Hi-Liner SG